Is this plume kit gas safe

Discussion in 'Plumbers' Talk' started by Rizo, Jun 5, 2014.

Page 1 of 3
  1. Rizo

    Rizo Member

    image.jpg Hi guys

    Long story short.
    Will this pass gas safe test?

    Ta
     
    Rizo, Jun 5, 2014
    #1
  2. meady

    meady Member

    Is that a bit of downpipe over the end of the flue??????
     
    meady, Jun 5, 2014
    #2
  3. meady

    meady Member

    And no it's not legal, that could be very dangerous
     
    meady, Jun 5, 2014
    #3
  4. metrokitchens

    metrokitchens Screwfix Select

    I would at a minimum rotate the hook 180 deg.
     
    metrokitchens, Jun 5, 2014
    #4
  5. meady

    meady Member

    What's your location mate as that needs looking at immediately
     
    meady, Jun 5, 2014
    #5
  6. tom.plum

    tom.plum Screwfix Select

    and its not weathered, the rains gonna pisssss throu the gap in the roof slats,
     
    tom.plum, Jun 5, 2014
    #6
  7. chippie244

    chippie244 Super Member

    That hook isn't going to hold much!
     
    chippie244, Jun 5, 2014
    #7
    metrokitchens likes this.
  8. Phil the Paver

    Phil the Paver Screwfix Select

    Its June the 5th, not April the 1st. A sad attempt at a joke, I hope anyway.:eek:
     
    Phil the Paver, Jun 5, 2014
    #8
  9. plumberboy

    plumberboy Well-Known Member

    LOL:p
     
    plumberboy, Jun 5, 2014
    #9
  10. Rizo

    Rizo Member

    You can see that its flattenned where its going through the roof. Its clear taped where its going through the roof sheet. Also it receives minimal rain as it is very near the wall.
    You guys reckon it needs doing again - properly?
     
    Rizo, Jun 6, 2014
    #10
  11. chippie244

    chippie244 Super Member

    Is there a rodding point on the elbow?
     
    chippie244, Jun 6, 2014
    #11
    metrokitchens likes this.
  12. Sean_ork

    Sean_ork Screwfix Select

    yes, and the wiring to your flood needs a little attention
     
    Sean_ork, Jun 6, 2014
    #12
  13. Rizo

    Rizo Member

    No. The originals dont have a rodding point either
     
    Rizo, Jun 6, 2014
    #13
  14. Rizo

    Rizo Member

    Why is that then? Wiring is fine. Coming out of the wall and into a junction box
     
    Rizo, Jun 6, 2014
    #14
  15. chippie244

    chippie244 Super Member

    The wiring is alright as long as they don't close the door.
     
    chippie244, Jun 6, 2014
    #15
  16. Sean_ork

    Sean_ork Screwfix Select

    how's the corrugated roofing flashed to the wall, looks like there's a ventilation gap from your picture
     
    Sean_ork, Jun 6, 2014
    #16
  17. chippie244

    chippie244 Super Member

    I'm not sure that you're allowed to have an awning pulley without an awning either, I'm certain there is a part P law about it.
     
    chippie244, Jun 6, 2014
    #17
    itchyspanner likes this.
  18. Rizo

    Rizo Member

    Rizo, Jun 6, 2014
    #18
  19. Rizo

    Rizo Member

    yawn!
     
    Rizo, Jun 6, 2014
    #19
  20. meady

    meady Member

    All joking aside mate, change it ASAPASAP
     
    meady, Jun 6, 2014
    #20
Page 1 of 3

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice