Recent Activity

Activity stream for all registered members at Screwfix Community Forum.

  1. Jord86 replied to the thread Metal web joists - Screwing down creaky floorboards.

    Check what glue has been used, if they just used PVA on the joints it's largely useless. As Dan Parkinson said, a polyurethane based...

    Jul 13, 2020 at 7:57 PM
  2. Wayners replied to the thread Gyproc thermaline board worth it?.

    This may help you decide https://www.mybuilder.com/questions/v/14947/using-50mm-polystyrene-instead-of-50mm-celotex-for-extension

    Jul 13, 2020 at 7:57 PM
  3. Joe the Plumber replied to the thread Shower bar mixer loose?.

    There may be a little cap on the end of the handle. Prise that off and there should be a screw to tighten the handle under it. If not,...

    Jul 13, 2020 at 7:56 PM
  4. Wayners replied to the thread The right paint for MDF desk?.

    Last diamond satin I used I struggle with the stuff. Hear it's improved... Johnstone's have this new Aqua Guard paint that looks good on...

    Jul 13, 2020 at 7:54 PM
  5. Jord86 liked Dan Parkinson's post in the thread Metal web joists - Screwing down creaky floorboards.

    Most chipboard flooring is glued down now. I'm about to glue 22 sheets of Cabershield+ down tomorrow.

    Jul 13, 2020 at 7:53 PM
  6. Powerelec replied to the thread Gyproc thermaline board worth it?.

    Sorry , I confused you, I meant I would use the ready stuck polystyrene, but is it really worth the cost . as it seems a lot of money....

    Jul 13, 2020 at 7:53 PM
  7. METRO MARK attached a file to the thread Current flow at certain points in circuit.

    HMM This guy had some bolt in products either side [ATTACH]

    hm.jpg Jul 13, 2020 at 7:51 PM
  8. Jord86 replied to the thread Gyproc thermaline board worth it?.

    Make your own.

    Jul 13, 2020 at 7:51 PM
  9. Den1690 replied to the thread Current flow at certain points in circuit.

    I will get one up sorry I meant bolt on

    Jul 13, 2020 at 7:50 PM
  10. ben100 posted a new thread.

    Shower bar mixer loose?

    I’ve got a shower bar mixer where the hot tap handle side is loose & doesn’t turn tight at all which means no water able to come out...

    Forum: Plumbers' Talk

    Jul 13, 2020 at 7:47 PM
  11. METRO MARK liked Jord86's post in the thread Hang vertical rad with brick screws?.

    Those will hold up a tank, you're overthinking this, either use them or 60-70mm 6.0/ no.12's woodscrews with brown plugs, if you need...

    Jul 13, 2020 at 7:43 PM
  12. Jord86 replied to the thread Hang vertical rad with brick screws?.

    Those will hold up a tank, you're overthinking this, either use them or 60-70mm 6.0/ no.12's woodscrews with brown plugs, if you need...

    Jul 13, 2020 at 7:42 PM
  13. Beacon replied to the thread Impossible exterior light.

    Didn't take photo but the 3-gang was straightforward, a live in looped along the 3 switches presumably then going to 3 accessories...

    Jul 13, 2020 at 7:41 PM
  14. Bazza replied to the thread Current flow at certain points in circuit.

    I am reading the words in your post but, I can make no sense of what you are asking. No matter what way round I juggle the words. Can...

    Jul 13, 2020 at 7:39 PM
  15. Wayners replied to the thread Gyproc thermaline board worth it?.

    Go with cheaper option but with the thermal board its easy to stick on wall with foam as is all stuck together ready to fit. Makes...

    Jul 13, 2020 at 7:37 PM
Loading...