led

  1. jimbobfruitbat

    Replacement of MR11 Halogen bulbs with MR11 LED

    Hi! We have 7x MR11 20W Halogen bulbs in our landing ceiling. I have bought 7x MR11 3W LED bulbs. Each pack is titled "6 Pack MR11 GU4 12-24V 3W LED Bulb, Cool White 6000K, Equivalent to 30W 20W Halogen Spotlight Bulb, 300LM, GU4 Bi-Pin Base, 120°Beam Angle, Non-Dimmable, for Hallway, Living...
  2. N

    Replacing T8 fluorescent tubes with LED tubes

    Is the LAP G13 T8 LED Tube 3600lm 24W 1778mm a direct replacement for a Philips tl-d 70w/840 6ft, in terms of size and wattage?
  3. J

    Dimmable bulbs and switches - recommendations needed

    Hi all, I asked on this forums recently about problems with my (LED) lights which are flickering. So far I was unable to figure out what the problem might be, so I thought I'd consider replacing the bulbs as well as the switches - and wanted to ask for your recommendations on LED bulbs (E14) and...
  4. M

    G4 LEDs

    Got this light which has 6x G4 bulbs. I would like to replace them with LEDs but they would not meet the minimum load 35W, all I can find is 12V 5W bulbs which gives 30W. Can I replace the transformer with 30W LED one ? Or can I just remove it completely and use 230V LEDs ? The secondary is...
  5. J

    Flickering dimmable LED lights

    Dear all, I seem to be having issues with my dimmable LED light bulbs / smart switches. I am not an electrician but I'll try my best to describe what's happening - any insight / advice would be greatly appreciated: I recently rennovated my flat, having electrician doing some new wiring, new...
  6. J

    Identify Fridge Model for replacement internal light

    Please help! My rental home has a Samsung side by side fridge freezer and the internal strip light in the back of the fridge has gone and I’m looking to replace it, but I haven’t got a scooby on the correct light to buy - hopefully by identifying the model I can find this out, or alternatively...
  7. N

    Dimmable LEDs and driver half-working

    Hello, I have a new 1-gang 2-way LED-specific traliling-edge push/rotary dimmable driver (max 100W) in my kitchen. The 2nd 2-way is a straight on/off that we don't use. The breakfast table side has a new ceiling strip light, 4x new 5W dimmable Gu10 LEDs (20W total). These all dim just fine, no...
  8. D

    Dim LED ‘Neon’ Light

    Disclaimer: No idea about the ins and outs of electronics so please explain like I’m 5. I have two LED ‘neon’ lights. It’s just an LED strip under some flexible gel-type plastic (excuse the ignorance on plastic types)...
  9. P

    Wiring 13A socket on lighting circuit

    I have led strips with transformer plugs which I need to connect to the lighting circuit so the light switch can control them. Is it ok if I add a 13A sockets above each cabinet to plug transformer plugs into?
  10. S

    LED ceiling light wiring

    Hi, Wondering if anyone could help. I am about to replace my ceiling lights with the modern led ceiling lights but noticed it only has two red wires coming out. The old ceiling rose has few sets of wires connected to the terminal block. Which wires do I need replace? See photos attached. Any...
  11. D

    Led light fitting dim

    Hi. I have just replaced an old, but working light fitting that had led bulbs in, with an led light fitting. It is wired into a 3 gang switch. When fitting I accidentally wired it into the fixed live and the light worked fine, just didn't turn off! Once I realized my mistake I wired it into the...
  12. D

    Replacing halogen spotlight downlighting with LEDs Thermal insulation.

    Any professional sparkys here able to weign in on this? I'm looking to replace some old (and hot) halogen downlights with LED downlights. I've seen Aussie videos stating that these are easier to insulate over than the old (toasty) halogen variants. I've been doing quite a bit of wiring work in...
  13. Kyba

    How do I open this light?

    It won't turn on and I'd like to see what's up
  14. A

    Kitchen LED Smart Lights

    Hi All, Not sure if this is a suitable forum for this, but I'm going crazy trying to work this out, when I feel it should be quite straight forward. Basically, I want to add some smart LED light strips in my kitchen. There are a number of different sections to my kitchen so will all need to be...
  15. K

    Mdf Shelves with Recessed LED profiles advise

    Hello I'm an absolute amateur in the third stage for my first DIY project of a display cabinet housed inside an unused chimney breast I have some 6mm recessed led profiles that I want to place into the front of the 18mm MDF Im concerned if I route out 6mm from the 18mm MDF to place the...
  16. R

    LED strip lights onto existing light circuit

    We have recently had a new kitchen installed and would like to install new 5w light strips or cabinet strips to the cabinets. The old kitchen had halogen cabinet lights that came on when the wall switch was pressed. The wiring has been left over and I would like the new LED lights to power on...
  17. U

    Led light switch

    Hi, I need a light switch (for toilet) that would indicate when the light is on at a glance (I'm thinking LED that goes on when light is on). I have solid doors and it happened few times already that the light was left on and noone noticed until opened the door few hours later. The only switches...
  18. S

    Dimmable downlights (SF code114PP). Trailing or leading edge operation.

    Can anyone tell me if these lights operate on a leading or trailing edge please. I want to control them with a Kosnic dimmer switch which I believe is trailing (negative) edge operated. The downlights are LAP code 21W51
  19. O

    Two gang LED light issue

    I have an electrical problem. I am a DIYer. I've a two gang switch and have just replaced some old 70s lights. I've matched the wiring but has an issue. Switch two works and switches light two on and off. Switch one however only dimly lights the first light. I've no idea why. I've not touched...
  20. T

    LED throughout kitchen new build

    Hi All, apologies in advance if any lingo is not right. I am in a new build, the kitchen has a 3 gang light switch with 2 operating the kitchen ceiling lights and the 3rd feeding into a junction box underneath a kitchen cupboard. I want to use the 3rd switch via the junction box to set up LED...
Back
Top