shower tray

hi Experts, i need advise on how to dela with very thin crack in shower tray which give very slow leak . have checked various repair options: Shower Tray Repair Kit Fix Cracks Holes Tiles Tub Bathtub White DIY Solution...

Don’t ask me how or why I did this as I’m already beating myself up no end. Brand new Mira stone resin shower tray in white. I dropped a tile on it and the result is a very small superficial damage chip in the tray. Any recommendations on how to fix and conceal this? There’s tonnes of products...

I have a 760x760 shower tray that I want to replace with a 760x1000 shower tray up stairs. Will I have to get a riser kit as well or can I make use of the existing one?

Hi all, i have been looking for quotes for someone to install a shower tray (1700 x 700). basically we have a crack in our current one so we have bought new - exactly same size. We do have a shower enclosure (sliding doors) but it's just a standard one. I have had a mixed bunch of quotes and so...

I’m planning to connect a shower trap to the waste pipes for a new shower tray. The waste outlet is located towards the wall in the center, so the waste pipes will need a 90-degree bend. I’ll need to make a cut near the existing Tee, but I’m concerned that if I don’t get it right the first time...

I’m laying down a 1200 x 760 stone resin on a floor that isn’t level. Manufacture instructions recommend a cement mix or silicone. Silicone seems like the simpler option but can this be used to level a shower tray? Or would a sand cement mix be better for this?

I’m planning to install a shower tray, but I’ve noticed it’s bowed by about 3mm, which is within the manufacturer’s tolerance. My concern is how to securely attach a shower screen, given that the tray isn’t perfectly flat. Do you have any advice on the best approach?

I’ve dry-fitted my shower tray waste. Can anyone spot any potential issues? (Please ignore the sawdust, I’ll clean everything before the final fit.)

I’m installing a shower tray and noticed a brush icon in the instructions labeled “PVC.” Does anyone know what this indicates?

After researching the debate between using a mortar mix or tile adhesive for laying a shower tray, I’ve decided to go with tile adhesive. Does anyone have any recommendations or thoughts on this? I was considering using the following product...

I’ve recently purchased a shower tray, and I noticed that the middle is slightly raised when I check it with a spirit level. Are the edges of a shower tray supposed to be completely flat, or is this normal? Should I be concerned about this affecting installation or water drainage?

Hi, We have a raised curved shower tray and the plinth/skirt is cracked. The height of the gap is 4" or 105mm; and try as I might I can only find the full kit. https://amzn.eu/d/jdxIbHI I've asked the supplier if they'll sell just the plinth, but have refused to do so. The only others I...

Please could anyone advise me on a temporary fix for my shower waste drain pipe. As you look down the shower tray drain there is a hole in the pipe about the size of a 1 pence. Is there anything I could use to seal it that would withstand the constant flow of water passing over and through it...

The waste hole for my shower tray is located in the middle, but the existing waste pipe is not aligned with it. Should I route the waste pipe under the floor to match the position of the waste hole, or is it possible to reroute it above the floor, given that the tray will be installed on a...

I'm about to install a shower tray onto caperboard, sealed with SBR primer followed by a sand/cement mix to level it off. The walls are 12mm nomoreply cement board. Due to the uneven floors, there's a gap as the floor slopes away (only a small gap though). There is also (due to me messing up...

Hi All I have a 1200 x 900 composite shower tray and a 1200 wide 8mm shower glass to go on top. I've bought a U-channel to bond on to the shower tray for the glass to sit in (along with a wall channel). What is the strongest method of bonding the metal channel to the composite tray please...

I fitted a 1600 x 800 shower tray a few weeks ago. After muh reading I decided to go with what the instructions said, the dreaded 5:1 sand and cement, with a bit of SBR added to the mix. The floor is a concrete sub floor so in order to get the drain under the tray I built a plinth out of CLS...

Hi All, First post, I need advice… I have a large 40kg dog who, in the summer, is prone to grass seeds in his toes and they need “soaking out”. Currently I have to lift him into the bath (not easy). What I really need is to replace the bath with a large rectangular deep shower tray, where I can...

Hi All, I have a 7 yr old new build house (Bloor) and have recently had to replace my double size shower tray as ours had cracked and was leaking water (turns out it wasn't properly supported no surprise). I've just replaced it with a heavy ceramic shower tray, plumbed in the waste, RE-wet...

I am currently doing a bathroom renovation and decided on fitting a Merlyn Level 25 stone resin shower tray. In the instructions, the first thing they get you to do is check that there isn't an excessive bow on all four sides. They do this by getting you to prop up the tray on four blocks of...